X3 TAPP Clutch XR Race Series Drive Belt for 400+ HP Can Am Maverick
Description
*This belt is recommended for all EVP.MOde Spec TAPP primary clutches calibrated for 400+ HP Can-Am Maverick X3's.
Due to the larger overall diameter and overdrive capability of the Tapp primary clutch, customers with 400+ horsepower X3’s used for drag racing should consider using our slightly longer WBB112 belt over the OEM length WBB383 belt.High horsepower cars on launch control can over shift beyond the length of the OEM belt on the initial hit. This can cause the belt to bottom out on the helix in the secondary clutch and/or rip the belt in half. The longer belt prevents this undesirable result. The EVP TAPP XR Race Series Belt features the same rock-solid performance and dependability countless customers (and all EVP racers) have relied on since introducing the EVP BADASS Belt lineup.
World's Best XR Race Series belts are manufactured with a larger Kevlar cord and feature a custom braid design marrying the layers of the belt for better shock absorption and increased cord pop-out resistance. An additional benefit includes being able to withstand more heat for increased overall strength and durability.
- Designed with larger Kevlar cord and a custom braid design for better shock absorption when landing
- Made from custom blend of two premium High Modulus Compounds holding the top and bottom layers together like super glue.
- Load tested to withstand the power of up to 600 hp machines.
- Impregnated with short Aramid Fibers for better heat resistance and belt-to-sheave adhesion.
ADDITIONAL FEATURES/BENEFITS:
- Race Proven Performance
- Manufacturing, quality control certifications: ISO-14001, ISO-9001, and IATF-16949
- Newly released design that has a larger Kevlar cord with a custom braid design to act as a shock absorber for HIGH HORSEPOWER TENSILE LOAD requirements
- New vulcanization process marrying the layers of the belt together around the cord, preventing premature separation of the layers
- Highest shock load rating to-date: Able to withstand the power of 600 hp machines
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom Cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature
- Latest bottom cog design for greater rotational efficiency at full shift
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature
- Kevlar cord (vs Polyester) wraps over bottom cogs for increased bottom cog strength and increased cord pop-out resistance
Fitment
Can-Am:
2017-2022 X3 Maverick / X3 MAX / X3 900 All Models with Tapp Primary Clutch
- Replaces OEM #’s 422280651 / 417300383 / 422280654 / 417300571 / 417300551 / 417300531 / 422280652
Warranty
Limited Belt Warranty Coverage
Evolution Powersports belts are covered against defects in material or workmanship under normal use during the warranty period.
- Warranty period: 1 year from date of purchase
- Valid only for belts purchased from EVP or an authorized dealer
- Replacement belts assume the remaining warranty period from the original purchase
- Claims must be submitted within 30 days of discovering the defect
- The belt may need to be returned for inspection at the customer’s expense
What Is Not Covered
This warranty does not cover any damage or failure not caused by a defect in material or workmanship. See table below for examples.
- Improper use or operating conditions
- Clutching issues or mechanical malfunctions
- Heat damage or belt wear
- Improper installation or break-in
Drive Belt Failures
Hour Glassing
Description: A narrow or worn section in the center of the belt.
Cause: When the drive clutch is spinning and the belt remains stationary.
Status: Not Warrantied
Cord Pop Out
Description: When the center cord separates from the belt.
Cause: Improper bonding.
Status: Warrantied
Flex Crack
Cause: The belt was bent/flexed improperly.
Status: Not Warrantied
Glazing
Description: The sides of the belt look shiny and overheated.
Cause: Belt slippage, overheating from improper clutching and/or abuse.
Status: Not Warrantied
Tearing
Description: The drive belt appears to have hit something and is starting to tear or has torn.
Cause: Worn or damaged clutches causing the clutches not to shift properly. Excessive use of brakes or jumping. The belt will bow and can catch the inner clutch housing.
Status: Not Warrantied
Delamination
Description: Separation of the belt layers.
Cause: Improper bonding of the belt layers.
Status: Warrantied
Broken Belt
Cause: Shock loading the belt will cause breakage. Driving at high speeds (overdrive) for long periods of time. Excessive engagement RPM. Improper gear ratio, clutch center-to-center distance. Jammed or locked drivetrain.
Status: Not Warrantied
Disintegration
Description: The drive belt has separated into pieces.
Cause: Can be caused by different belt conditions such as hour glassing, glazing, flex cracks, or misalignment. Plugged or restricted air intake to clutch housing.
Excessive heat build-up is the main cause of disintegration.
Status: Not Warrantied
Instructions
Product Information
Product Information
Shipping & Returns
Shipping & Returns
X3 TAPP Clutch XR Race Series Drive Belt for 400+ HP Can Am Maverick
X3 TAPP Clutch XR Race Series Drive Belt for 400+ HP Can Am Maverick
Description
*This belt is recommended for all EVP.MOde Spec TAPP primary clutches calibrated for 400+ HP Can-Am Maverick X3's.
Due to the larger overall diameter and overdrive capability of the Tapp primary clutch, customers with 400+ horsepower X3’s used for drag racing should consider using our slightly longer WBB112 belt over the OEM length WBB383 belt.High horsepower cars on launch control can over shift beyond the length of the OEM belt on the initial hit. This can cause the belt to bottom out on the helix in the secondary clutch and/or rip the belt in half. The longer belt prevents this undesirable result. The EVP TAPP XR Race Series Belt features the same rock-solid performance and dependability countless customers (and all EVP racers) have relied on since introducing the EVP BADASS Belt lineup.
World's Best XR Race Series belts are manufactured with a larger Kevlar cord and feature a custom braid design marrying the layers of the belt for better shock absorption and increased cord pop-out resistance. An additional benefit includes being able to withstand more heat for increased overall strength and durability.
- Designed with larger Kevlar cord and a custom braid design for better shock absorption when landing
- Made from custom blend of two premium High Modulus Compounds holding the top and bottom layers together like super glue.
- Load tested to withstand the power of up to 600 hp machines.
- Impregnated with short Aramid Fibers for better heat resistance and belt-to-sheave adhesion.
ADDITIONAL FEATURES/BENEFITS:
- Race Proven Performance
- Manufacturing, quality control certifications: ISO-14001, ISO-9001, and IATF-16949
- Newly released design that has a larger Kevlar cord with a custom braid design to act as a shock absorber for HIGH HORSEPOWER TENSILE LOAD requirements
- New vulcanization process marrying the layers of the belt together around the cord, preventing premature separation of the layers
- Highest shock load rating to-date: Able to withstand the power of 600 hp machines
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom Cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature
- Latest bottom cog design for greater rotational efficiency at full shift
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature
- Kevlar cord (vs Polyester) wraps over bottom cogs for increased bottom cog strength and increased cord pop-out resistance
Fitment
Can-Am:
2017-2022 X3 Maverick / X3 MAX / X3 900 All Models with Tapp Primary Clutch
- Replaces OEM #’s 422280651 / 417300383 / 422280654 / 417300571 / 417300551 / 417300531 / 422280652
Warranty
Limited Belt Warranty Coverage
Evolution Powersports belts are covered against defects in material or workmanship under normal use during the warranty period.
- Warranty period: 1 year from date of purchase
- Valid only for belts purchased from EVP or an authorized dealer
- Replacement belts assume the remaining warranty period from the original purchase
- Claims must be submitted within 30 days of discovering the defect
- The belt may need to be returned for inspection at the customer’s expense
What Is Not Covered
This warranty does not cover any damage or failure not caused by a defect in material or workmanship. See table below for examples.
- Improper use or operating conditions
- Clutching issues or mechanical malfunctions
- Heat damage or belt wear
- Improper installation or break-in
Drive Belt Failures
Hour Glassing
Description: A narrow or worn section in the center of the belt.
Cause: When the drive clutch is spinning and the belt remains stationary.
Status: Not Warrantied
Cord Pop Out
Description: When the center cord separates from the belt.
Cause: Improper bonding.
Status: Warrantied
Flex Crack
Cause: The belt was bent/flexed improperly.
Status: Not Warrantied
Glazing
Description: The sides of the belt look shiny and overheated.
Cause: Belt slippage, overheating from improper clutching and/or abuse.
Status: Not Warrantied
Tearing
Description: The drive belt appears to have hit something and is starting to tear or has torn.
Cause: Worn or damaged clutches causing the clutches not to shift properly. Excessive use of brakes or jumping. The belt will bow and can catch the inner clutch housing.
Status: Not Warrantied
Delamination
Description: Separation of the belt layers.
Cause: Improper bonding of the belt layers.
Status: Warrantied
Broken Belt
Cause: Shock loading the belt will cause breakage. Driving at high speeds (overdrive) for long periods of time. Excessive engagement RPM. Improper gear ratio, clutch center-to-center distance. Jammed or locked drivetrain.
Status: Not Warrantied
Disintegration
Description: The drive belt has separated into pieces.
Cause: Can be caused by different belt conditions such as hour glassing, glazing, flex cracks, or misalignment. Plugged or restricted air intake to clutch housing.
Excessive heat build-up is the main cause of disintegration.
Status: Not Warrantied
Instructions
Original: $224.95
-65%$224.95
$78.73Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Description
*This belt is recommended for all EVP.MOde Spec TAPP primary clutches calibrated for 400+ HP Can-Am Maverick X3's.
Due to the larger overall diameter and overdrive capability of the Tapp primary clutch, customers with 400+ horsepower X3’s used for drag racing should consider using our slightly longer WBB112 belt over the OEM length WBB383 belt.High horsepower cars on launch control can over shift beyond the length of the OEM belt on the initial hit. This can cause the belt to bottom out on the helix in the secondary clutch and/or rip the belt in half. The longer belt prevents this undesirable result. The EVP TAPP XR Race Series Belt features the same rock-solid performance and dependability countless customers (and all EVP racers) have relied on since introducing the EVP BADASS Belt lineup.
World's Best XR Race Series belts are manufactured with a larger Kevlar cord and feature a custom braid design marrying the layers of the belt for better shock absorption and increased cord pop-out resistance. An additional benefit includes being able to withstand more heat for increased overall strength and durability.
- Designed with larger Kevlar cord and a custom braid design for better shock absorption when landing
- Made from custom blend of two premium High Modulus Compounds holding the top and bottom layers together like super glue.
- Load tested to withstand the power of up to 600 hp machines.
- Impregnated with short Aramid Fibers for better heat resistance and belt-to-sheave adhesion.
ADDITIONAL FEATURES/BENEFITS:
- Race Proven Performance
- Manufacturing, quality control certifications: ISO-14001, ISO-9001, and IATF-16949
- Newly released design that has a larger Kevlar cord with a custom braid design to act as a shock absorber for HIGH HORSEPOWER TENSILE LOAD requirements
- New vulcanization process marrying the layers of the belt together around the cord, preventing premature separation of the layers
- Highest shock load rating to-date: Able to withstand the power of 600 hp machines
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom Cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature
- Latest bottom cog design for greater rotational efficiency at full shift
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature
- Kevlar cord (vs Polyester) wraps over bottom cogs for increased bottom cog strength and increased cord pop-out resistance
Fitment
Can-Am:
2017-2022 X3 Maverick / X3 MAX / X3 900 All Models with Tapp Primary Clutch
- Replaces OEM #’s 422280651 / 417300383 / 422280654 / 417300571 / 417300551 / 417300531 / 422280652
Warranty
Limited Belt Warranty Coverage
Evolution Powersports belts are covered against defects in material or workmanship under normal use during the warranty period.
- Warranty period: 1 year from date of purchase
- Valid only for belts purchased from EVP or an authorized dealer
- Replacement belts assume the remaining warranty period from the original purchase
- Claims must be submitted within 30 days of discovering the defect
- The belt may need to be returned for inspection at the customer’s expense
What Is Not Covered
This warranty does not cover any damage or failure not caused by a defect in material or workmanship. See table below for examples.
- Improper use or operating conditions
- Clutching issues or mechanical malfunctions
- Heat damage or belt wear
- Improper installation or break-in
Drive Belt Failures
Hour Glassing
Description: A narrow or worn section in the center of the belt.
Cause: When the drive clutch is spinning and the belt remains stationary.
Status: Not Warrantied
Cord Pop Out
Description: When the center cord separates from the belt.
Cause: Improper bonding.
Status: Warrantied
Flex Crack
Cause: The belt was bent/flexed improperly.
Status: Not Warrantied
Glazing
Description: The sides of the belt look shiny and overheated.
Cause: Belt slippage, overheating from improper clutching and/or abuse.
Status: Not Warrantied
Tearing
Description: The drive belt appears to have hit something and is starting to tear or has torn.
Cause: Worn or damaged clutches causing the clutches not to shift properly. Excessive use of brakes or jumping. The belt will bow and can catch the inner clutch housing.
Status: Not Warrantied
Delamination
Description: Separation of the belt layers.
Cause: Improper bonding of the belt layers.
Status: Warrantied
Broken Belt
Cause: Shock loading the belt will cause breakage. Driving at high speeds (overdrive) for long periods of time. Excessive engagement RPM. Improper gear ratio, clutch center-to-center distance. Jammed or locked drivetrain.
Status: Not Warrantied
Disintegration
Description: The drive belt has separated into pieces.
Cause: Can be caused by different belt conditions such as hour glassing, glazing, flex cracks, or misalignment. Plugged or restricted air intake to clutch housing.
Excessive heat build-up is the main cause of disintegration.
Status: Not Warrantied
